Fabrication and Assembly Guide - Revision history

Hishinuma: /* Ordering standard parts */

2017-10-13T01:54:50Z

‎Ordering standard parts

2015-06-09T16:48:56Z

‎Building cables

2015-06-09T16:48:20Z

‎Building cables

2015-06-09T16:46:43Z

‎Building cables

2015-06-09T16:42:37Z

‎Assembling MINIscope housing

2015-05-01T16:13:04Z

‎Flashing DAQ firmware

2015-05-01T16:12:20Z

‎Flashing DAQ firmware

2015-05-01T16:07:35Z

‎Assembling electronics

2015-05-01T16:04:01Z

‎Assembling electronics

2015-05-01T16:03:28Z

‎Assembling electronics

← Older revision		Revision as of 01:54, 13 October 2017
Line 20:		Line 20:

	Grin lenses can be ordered through [http://www.grintech.de/ Grintech].		Grin lenses can be ordered through [http://www.grintech.de/ Grintech].
		+
		+	Grin lenses can be ordered through [https://welcome.gofoton.com/product/imaging_lens/ GoFoton]

	'''Please refer to the [[Part Lists\|part list]] for part numbers and suppliers.'''		'''Please refer to the [[Part Lists\|part list]] for part numbers and suppliers.'''

@@ Line 31: / Line 31: @@
 == Building cables ==
-More assembly information can be found here: [[File:CableAssembly]].
+More assembly information can be found here: [[File:CableAssembly.pdf]].
 == Assembling electronics ==

@@ Line 31: / Line 31: @@
 == Building cables ==
-More assembly information can be found [[File:CableAssembly|here]].
+More assembly information can be found here: [[File:CableAssembly]].
 == Assembling electronics ==

← Older revision		Revision as of 16:46, 9 June 2015
Line 31:		Line 31:

	== Building cables ==		== Building cables ==
		+	More assembly information can be found [[File:CableAssembly\|here]].

	== Assembling electronics ==		== Assembling electronics ==

← Older revision		Revision as of 16:42, 9 June 2015
Line 27:		Line 27:

	[[File:MINIscopeExploded.png\|400px]]		[[File:MINIscopeExploded.png\|400px]]
		+
		+	[[File:HousingAssembly.png\|400px]]

	== Building cables ==		== Building cables ==

@@ Line 41: / Line 41: @@
 === Writing image to EEPROM ===
 === Setting jumpers to boot from image on EEPROM ===
 == Installing DAQ software ==

← Older revision		Revision as of 16:12, 1 May 2015
Line 36:		Line 36:

	== Flashing DAQ firmware ==		== Flashing DAQ firmware ==
		+	Firmware must be uploaded into the EEPROMS of the DAQ hardware. You can either request a preprogrammed EEPROMS from us (which just plugs into the DAQ hardware) or you can flash the firmware yourself. In order to do it yourself you will need the Cypress Control Center which can be found [http://www.cypress.com/?rID=34870 here].
		+
		+	=== Setting jumpers for writing to EEPROM ===
		+
		+	=== Writing image to EEPROM ===
		+
		+	=== Setting jumpers to boot from image on EEPROM ===

	== Installing DAQ software ==		== Installing DAQ software ==

@@ Line 33: / Line 33: @@
 The CMOS imaging sensor PCB and LED excitation PCB can be soldered and assembled in your lab or you can send the PCB and electronics out to an assembly house (we suggest using Sierra Circuits). Electronics part lists can be found [[All Downloads|here]].
-THE DAQ PCB should be set out for assembly due to the complexity of some of its parts.
+The DAQ PCB should be sent out for assembly due to the complexity of some of its parts. The Bill of Materials (BOM) can be found [[All Downloads|here]].
 == Flashing DAQ firmware ==
 == Installing DAQ software ==